Check out Mr Freeze's 1952 Chevrolet named Big Bertha at MyRideisMe.com

/Garage/Mr Freeze

Mr Freeze
	Gilbert, AZ, USA Joined: 06/23/2007

My Lifestyles:
Show Trucks, Low Rider, H.A.M.B., Build-It, Drive-It, Custom Rodder, Street Rodder, Old-School, Restorer, Builder, Hot Rodder

Ford Falcon "Redsled"

Ford Pickup "40 SOLD"

Ford Pickup "Workhorse 40 SOLD"

My Ride is Me "Frankin T"

Ford Falcon "Cumulous SOLD"

Chevrolet APV "Big Bertha"

Datsun 620 Pickup "Datsoon SOLD"

Chevrolet C-10 "LoFat"

Fiat Coupe "STUFFED"

Fiat Coupe "ON HOLD 4 NOW"

Chevrolet C-10 "No Parkin"

BMW Isetta "U R O"

Flag this garage as inappropriate

Chevrolet APV "Big Bertha"

Drivetrain:
455 Olds Toronodo

Future project

I needed another project!!!

Give me a Name

sitting on the toronado front clip

FWD 455 olds clip, torsionbar suspension

Cool patina

the new crossmember for the removeable interchangeable rear section

body crane

temp roller section

the beast

laid on the ground

New grill. Wanted to use the original but the supports were cut out and it was bent.

Comments:

johnnychrome	03-10-2010 12:09 PM That is awesome!!! Do you still have it? Any progress? Someone here on the north coast of ohio has a Chevy c30 (73~87 body) that employs the same basic principal, though I doubt it has interchangable beds. The fella used tandem axles with a huge amount of drop in the center that put the ramps about 10" from terra-firma. The first time I sah it I thaught they used a 4x4 and just left tha rear axle out of the equasion. Then thaught it must be riding on the suspension stops to sit that low... then realised what it was. It had a tire rack up high on the front of the bed as if it were built to haul a race car but I saw it doing duty as a wrecker.
DiedelsonKustoms	03-03-2009 11:17 AM Hello Mr Freeze, I found your Chevy COE Project. I think I would be A very Cool Truck when it is finished. Specially with the divarant Interchanceable rear sections. How fare are you with the truck.? Have fun Diedelson
kastoo	02-17-2008 11:48 PM Wow! That's even a lot cooler than I imagined!
Mr Freeze	01-29-2008 12:59 PM My plan for this ride is fully interchanceable rear sections. Initially I will build a standard pickup bed and then a light duty ramp bed. These will be connected via two receiver hitches and an upright bolt mount. There will be a quick disconnect for the brakelines and a electrical plug.
gtobob	01-04-2008 12:34 AM Hey, I miss you bro! See you in April at Speedworld! boB
LIL_NEWT	12-27-2007 11:11 AM I took one of those and stretched it 38 in. and made it in to a crew cab. Then put it on a 1 ton chassis. The guy never finished it though.
kastoo	12-16-2007 2:25 PM I'm still waiting unpatiently! This will be real neat!
pikesan	09-25-2007 3:12 AM Holy Crap Rob! What's your plan for that thing?

Only registered members can leave comments.

Automotive Rubber Parts & Weatherstrpping

fine art, hot rod art, motorcycle, oil painting

Custom Rendering & Pinstriping; hot rods and kustoms

www.hotrodsbyglen.net/index.html	Hotrod builder/Friend
www.pbase.com/socheap	friend